reliance 606 water heater manual

The Reliance 606 water heater is a popular choice for residential use, offering efficient and reliable performance. This manual provides essential guidance for installation, operation, and maintenance to ensure optimal functionality and safety.

Installation

Installing the Reliance 606 water heater requires careful preparation and adherence to safety guidelines. Begin by reading the General Safety section and ensuring the site is properly prepared. Check local plumbing and electrical codes for compliance. Ensure all connections are secure and correctly sized. Proper positioning and leveling of the unit are crucial for efficient operation.

Preparing for Installation

Before installing the Reliance 606 water heater, ensure all necessary preparations are completed to avoid complications. Begin by reading the entire manual, paying special attention to the General Safety section; Verify that the installation location complies with local plumbing and electrical codes. For gas models, ensure proper ventilation and combustion air supply are available. If installing an electric model, confirm the electrical circuit meets the heater’s voltage and amperage requirements. Gather all tools and materials, including a drain pan, water shut-off valves, and appropriate piping materials. For gas models, check the gas supply line for leaks and ensure it is sized correctly. If replacing an old water heater, drain the existing unit and disconnect all connections before proceeding. Always follow the manufacturer’s instructions for specific models, such as the Reliance 606 Series, to ensure a safe and proper setup. If unsure about any step, consult a licensed professional to avoid potential hazards.

Filling the Water Heater

Filling the Reliance 606 water heater is a critical step to ensure proper operation and prevent damage. Before filling, ensure the tank is completely empty and all valves are in the correct position. Open the cold water inlet valve and allow the tank to fill with water. Check for leaks at all connections during this process. Once the tank is full, turn on the hot water faucet nearest to the heater to verify water flow. For gas models, ensure the gas supply is turned off during filling to prevent accidental ignition. If the water heater is equipped with a drain valve, inspect it for proper function and replace the washer if necessary. Never operate the heater unless it is completely full of water, as this can cause damage to the heating elements or tank. After filling, follow the lighting instructions provided in the manual to restart the heater. Regularly draining and refilling the tank can help maintain efficiency and extend the lifespan of the appliance.

Operation

Operate the Reliance 606 water heater by turning on the power and setting the desired temperature. Ensure the temperature-pressure relief valve is functioning properly. Regularly check the water flow and adjust settings as needed for efficient performance.

Starting Up the Water Heater

To start up the Reliance 606 water heater, first ensure it is properly filled with water, as outlined in the filling section. Turn the power supply to the unit on and set the desired temperature using the thermostat. For gas models, ensure the gas supply is turned on and follow the lighting instructions provided in the manual. Once the water heater is operational, check the temperature-pressure relief valve to ensure it is functioning correctly. Allow the unit to heat the water for the recommended time before using the hot water supply. If the water heater does not activate, refer to the troubleshooting section for common issues and solutions. Always follow safety guidelines and manufacturer instructions to avoid potential hazards.

For gas models, ensure the pilot light is lit according to the instructions. If the water heater is not functioning, check the power and gas connections. Proper startup ensures efficient and safe operation of the unit.

Maintenance

Regular maintenance of the Reliance 606 water heater ensures long-term efficiency and safety. Clean the unit periodically, check the anode rod for corrosion, and inspect the temperature-pressure relief valve. Ensure proper ventilation and drain sediment to prevent damage;

Cleaning the Water Heater

Cleaning the Reliance 606 water heater is essential for maintaining its efficiency and prolonging its lifespan. Start by turning off the power and water supply to the unit. Drain the tank partially to remove sediment buildup, which can affect performance. Use a garden hose to flush out debris and mineral deposits. Inspect the anode rod and replace it if corroded, as it protects the tank from rust. Check the temperature-pressure relief valve for proper function and ensure it is free from blockages. Clean the venting system to ensure proper airflow and combustion. For electric models, wipe down the exterior and internal components gently to prevent dust accumulation. Regular flushing of the tank and checking for leaks will help maintain optimal operation. Always refer to the manual for specific instructions tailored to your model;

Troubleshooting

Common issues with the Reliance 606 water heater include no hot water, leaks, or error codes. Check the power supply, thermostat settings, and drain valves. Ensure proper ventilation and gas supply for gas models. Consult the manual or contact a technician for unresolved issues.

Common Issues and Solutions

Like any appliance, the Reliance 606 water heater may encounter issues during its operation. One common problem is a lack of hot water, which can be resolved by checking the power supply, thermostat settings, and ensuring the water heater is properly filled. Leaks are another frequent concern and often result from loose connections or worn-out washers. Tightening fittings or replacing damaged components can address this issue. If the water heater is in lockout mode, it may be due to overheating or a faulty temperature-pressure relief valve. Resetting the heater and ensuring proper ventilation can resolve this. Additionally, error codes on the display indicate specific malfunctions, such as sensor issues or ignition problems. Consulting the manual or contacting a professional is recommended for complex repairs. Regular maintenance, such as cleaning sediment and checking gas lines, helps prevent many of these issues. Always follow safety guidelines when troubleshooting to avoid further damage or safety risks.

Safety Precautions

When working with the Reliance 606 water heater, it is essential to follow all safety guidelines to ensure safe operation and prevent potential hazards. Always read the manual thoroughly before installation, operation, or maintenance. Ensure the water heater is installed correctly, adhering to local codes and regulations. Never use the water heater in manufactured (mobile) homes, as it is not designed for such applications. Proper ventilation is critical to avoid gas buildup; ensure the area is well-ventilated and free from flammable vapors. Keep the water heater away from combustible materials and ensure no open flames are nearby. Avoid touching electrical components with wet hands or while standing in water to prevent electrical shock. Never modify the water heater or its components, as this can lead to unsafe conditions. Always follow the manufacturer’s instructions for temperature settings to avoid scalding. In case of a gas leak or malfunction, turn off the gas supply and electricity immediately and contact a qualified technician. Regular maintenance by a professional is recommended to ensure safe and efficient operation.

Technical Specifications and Warranty

The Reliance 606 water heater is designed for residential use, offering a 55-gallon capacity and a 4.5kW heating element for efficient water heating. It features a durable construction with a galvanized steel tank and an electric heating system. The unit operates on 240-volt electricity and is designed for lowboy installation, making it ideal for spaces with height constraints. The water heater is certified by GAMA and meets safety standards for residential gas and electric water heaters. Dimensions are compact, measuring 52 inches in height and 20 inches in diameter, allowing for flexible placement in most homes.

The warranty for the Reliance 606 includes a 6-year limited tank warranty and a 2-year limited warranty on parts. For warranty claims, contact the local dealer where the water heater was purchased. The product is manufactured by A.O. Smith, a trusted name in water heating solutions, ensuring reliability and performance. Proper installation and maintenance are required to uphold the warranty terms and ensure long-term functionality.

The Reliance 606 water heater is a reliable and efficient solution for residential water heating needs. With its 55-gallon capacity and 4.5kW heating element, it provides consistent hot water supply while maintaining energy efficiency. The compact lowboy design makes it ideal for installations where space is limited. By following the guidelines outlined in this manual, users can ensure optimal performance, safety, and longevity of the appliance.

The warranty coverage, including a 6-year limited tank warranty and a 2-year parts warranty, offers peace of mind for homeowners. Proper installation, regular maintenance, and adherence to safety precautions are essential to maximize the heater’s efficiency and lifespan. For those seeking a dependable and durable water heating solution, the Reliance 606 is a strong choice.

Always refer to the manual for specific instructions and recommendations to ensure the Reliance 606 operates safely and effectively in your home.